My shopping cart
Your cart is currently empty.
Continue ShoppingQSC AcousticDesign Series Surface-Mount Loudspeaker
The QSC AcousticDesign™ series offers integrators a premium quality installed sound solution where performance, coverage, and aesthetics are paramount. Combined with unprecedented ease-of-installation and high weather resistance, the AcousticDesign™ Series provides integrators a versatile and confident install solution.
Installers will appreciate the award-winning X-Mount™ system included with each full-range AcousticDesign™ model. This ingenious mounting solution achieves unprecedented ease-of-installation in horizontal, vertical, wall, or ceiling deployments. Knurled surfaces at the pivot planes ensure the load will not drift or sag over time. Articulation marks allow pre-configuration of the X-Mount™ while on the ground with no special tools required. Once secure, the loudspeaker installs in seconds, allowing the installer to work safer, smarter, and faster with repeatable results.
To further enhance performance and speed of install with optimum result, advanced voicing filter sets using QSC Intrinsic Correction™ techniques are obtainable via the Q-SYS Platform including CXD Series amplifiers for a complete QSC systems solution.
Effective Frequency Range | 68 Hz - 20 kHz |
Rated Noise Power/Voltage | 50 Watts/ 20 volts (rms) |
Broadband Sensitivity | 87 dB SPL |
Coverage Angle (-6 dB) | 120° conical DMT |
Directivity Factor (Q) | 6 |
Directivity Index | 8 dB |
Maximum Continuous SPL | 104 dB |
Maximum Peak SPL | 110 dB |
Rated Impedance | 8 ohms |
Recommended Amplifier Power | 100 watts |
Transformer Taps | 70 V: 30, 15, 7.5, 3.75 W and 8O bypass |
Transformer Taps | 100V: 30, 15, 7.5 W and 8O bypass |
HF Transducer | 0.75-inch silk dome tweeter / 0.75-inch voice coil, horn loaded |
LF Transducer | 4.5-inch weather resistant paper cone woofer/ 1-inch / 25 mm voice coil |
Input Connector Type | Euroblock connector with parallel output terminals |
Enclosure Materials | Painted ABD Polymer |
Grille Material | Powder coated aluminium |
X-Mount Material | Powder coated aluminium |
Ingress Protection | IP-54 |
Operating Environment | Designed for indoor and outdoor use |
Testing Method #1 | Salt fog: MIL-STD-810G Method 509.5 for 100 hrs |
Testing Method #2 | Humidity: MIL-STD-810G Method 507.5, Natural cycle B2, cyclic high RH for 7 days |
Testing Methods #3 | High and low temperature: tested to QSC internal standards between -20° and 50° C |
Product Weight | 6.5 lb |
Product Dimension (H x W x D) | 10.27" x 6.33" x 6.42" |
Effective Frequency Range | 60 Hz - 20 kHz |
Rated Noise Power/Voltage | 100 W |
Broadband Sensitivity | 86 dB SPL |
Coverage Angle (-6 dB) | 115° conical DMT |
Directivity Factor (Q) | 6.9 |
Directivity Index | 7 dB |
Maximum Continuous SPL | 106 dB |
Maximum Peak SPL | 112 dB |
Rated Impedance | 8 ohms |
Recommended Amplifier Power | 100 watts |
Transformer Taps | 70 V: 7.5, 15, 7.5, 3.75 W and 6O bypass |
Transformer Taps | 100V: n/a, 15, 7.5 W and 6O bypass |
HF Transducer | 1-inch damped fabric dome tweeter, 1-inch voice coil |
LF Transducer | 5.25-inch paper cone woofer, 1-inch voice coil |
Input Connector Type | Euroblock connector with parallel output terminals |
Enclosure Materials | Painted ABS Polymer |
Grille Material | Powder coated aluminium |
X-Mount Material | Powder coated aluminium |
Ingress Protection | IP-54 |
Operating Environment | Designed for indoor and outdoor use |
Shipping Weight | 20.2 lb |
Product Dimension (H x W x D) | 11.3" x 6.9" x 6.8" |
Effective Frequency Range | 60 Hz - 20 kHz |
Rated Noise Power/Voltage | 150 watts / 35 volts (rms) |
Broadband Sensitivity | 89 dB SPL |
Coverage Angle (-6 dB) | 105° conical DMT |
Directivity Factor (Q) | 5 |
Directivity Index | 7 dB |
Maximum Continuous SPL | 110 dB |
Maximum Peak SPL | 116 dB |
Rated Impedance | 8 ohms |
Recommended Amplifier Power | 300 watts |
Transformer Taps | 70 V: 60, 30, 15, 7.5 W and 8O bypass |
Transformer Taps | 100V: 60, 30, 15 W and 8O bypass |
HF Transducer | 1 inch silk dome tweeter/ 1 inch voice coil, horn loaded |
LF Transducer | 6.5 inch weather resistant paper cone woofer / 1.5 inch / 38 mm voice coil |
Input Connector Type | Euroblock connector with parallel output terminals |
Enclosure Material | Painted ABD polymer |
Grille Material | Powder coated aluminum |
X-Mount Material | Powder coated aluminum |
Ingress Protection | IP-54 |
Operating Environment | Designed for indoor and outdoor use |
Testing Method #1 | Salt fog: MIL-STD-810G Method 509.5 for 100 hrs. |
Testing Method #2 | Humidity: MIL-STD-810G Method 507.5, Natural cycle B2, cyclic high RH for 7 days |
Testing Methods #3 | High and low temperature: tested to QSC internal standards between -20° and 50° C |
Product Weight | 13.6 lb |
Product Dimension (H x W x D) | 14.4" x 8.5" x 8.5" |
Frequency Range | 55 Hz to 20 kHz |
Noise Rating | Noise Power/Voltage: 200 W/40 V RMS |
Sensitivity | 90 dB SPL |
Coverage Angle | 105° at -6 dB |
Directivity | Factor: Q = 7 Index: 9 dB |
SPL | Maximum Continuous SPL: 113 dB, Maximum Peak SPL: 119 dB |
Impedance | 8 Ohm rated |
Amplifier Power | 400 W |
Transformer Taps | 70 V: 60, 30, 15, 7.5 W and 8 Ohm bypass 100 V: 60, 30, 15 W and 8 Ohm bypass |
HF Transducer | 1.0" (25.4 mm) exit/1.4" (35.6 mm) voice-coil compression driver |
LF Transducer | 8.0" (203.2 mm) weather-resistant paper cone woofer, 2.0" (50.8 mm) voice-coil |
Input Connector | Euroblock connector with parallel output terminals |
Enclosure Material | Painted ABS polymer |
Grille | Powder-coated aluminum |
Enclosure Characteristics | Ingress Protection: IP54, Operating Environment: Indoor/Outdoor |
Testing Parameters | The AD Series loudspeakers qualified for outdoor use using the following tests, Salt fog: MIL-STD-810G Method 509.5 for 100 hours, Humidity: MIL-STD-810G Method 507.5, Natural cycle B2, cyclic high RH for 7 days, High and low temperature tested according to QSC internal standards between -4 to 122°F (-20 to 50°C) |
Operating Temperature Range | -4 to 122°F (-20 to 50°C) |
Product Dimensions | 17.3 x 10.0 x 9.9" (440.0 x 254.0 x 251.0 mm) |
Product Weight | 24.1 lb (11.0 kg) |
Effective frequency range | 50 Hz - 19 kHz |
Rated noise power / voltage | 250 watts / 45 volts (rms) |
Broadband sensitivity | 92 dB SPL |
Coverage angle (-6 dB) | 90° conical DMT |
Directivity factor (Q) | 10 |
Directivity Index | 10 dB |
Maximum continuous SPL | 116 dB |
Maximum peak SPL | 122 dB |
Rated impedance | 8 ohms |
Recommended amplifier power (loudspeaker "program" | 500 watts |
Transformer taps | 70 V: 100, 50, 25, 12.5 W and 8O bypass; 100V: 100, 50, 25 W and 8O bypass |
HF transducer | 1-inch exit / 1.4-inch voice coil compression driver |
LF transducer | 10-inch weather resistant paper cone woofer; 2.5-inch / 64 mm voice coil |
Input connector type | Euroblock connector with parallel output terminals |
Enclosure material | Painted ABS polymer |
Grille material | Powder coated aluminum |
X-Mount material | Powder coated aluminum |
Ingress protection | IP-54 |
Operating environment | Designed for indoor and outdoor use |
Effective frequency range1 | 52 Hz - 20 kHz |
Rated noise power / voltage | 300 watts / 50 volts (rms) |
Broadband Sensitivity3 | 95 dB SPL |
Coverage angle (-6 dB) | 75° conical DMT |
Directivity factor (Q) | 12 |
Directivity Index | 11 dB |
Maximum continuous SPL4 | 120 dB |
Maximum peak SPL4 | 126 dB |
Rated impedance | 8 ohms |
Recommended amplifier power (loudspeaker "program | 600 watts |
Transformer taps | n/a |
HF transducer | 1-inch exit / 1.4-inch voice coil compression driver |
LF transducer | 12-inch weather resistant paper cone woofer, 2.5-inch / 64 mm voice coil |
Input connector type | Euroblock connector with parallel output terminals |
Enclosure material | Painted ABS polymer |
Grille material | Powder coated aluminum |
Sign up for our mailing list to receive new product alerts, special offers, and coupon codes.
© 2023 avBYFP | Powered by Shopify